Your hygrometer is in the wrong place
The humidity number everyone repeats is a canopy number, and almost everyone measures it on a tent wall. The gap between those two readings is where rot starts.
November is the month most growers look at a hygrometer constantly. There is a drying room to watch, jars to check, and a tent that has started behaving differently now the heat is on.
So it is a good month to notice that the reading is probably wrong. Not the device. The place you put it.
Two readings, one room
Clip a second hygrometer into the middle of a dense flowering canopy and leave the first one on the tent wall where it has always been. Check them an hour before lights off.
They will not agree, and the canopy will read higher. In a full tent with a tight canopy the gap is often substantial, because that is where the water is: a plant transpires constantly, and dense foliage holds that moist air against itself instead of letting it mix with the room.
The wall sensor is reading the room. The canopy sensor is reading where the plant actually lives, and where bud rot gets started. Rot does not begin in the open air of a tent. It begins in the still, saturated pocket inside the biggest cola, which is the part of the tent furthest from any sensor anybody owns.
Why this specifically bites in flower
A seedling barely moves water. A tent full of week-seven plants moves a lot of it, and the canopy gets denser in exactly the weeks the buds get most vulnerable.
So the gap widens over a run. A tent that genuinely sat at 55 percent in week two can have a canopy sitting much higher in week seven, while the wall sensor shows a number that has barely moved. Nothing looks wrong. You are hitting your target, on the device you are reading.
Then you find rot in a cola in week eight and conclude you were unlucky.
Where to actually put it
At canopy height, in the plants, not on the wall. Clip it to a stake or hang it from the trellis so the sensor sits among the buds rather than in open air.
Move it as the plants grow. A sensor set at canopy height in week one is below the canopy by week five, which is a different reading again.
Keep one on the wall too. Two numbers is the useful setup, because the difference between them tells you whether air is actually moving through the canopy. A big gap means it is not, and that is actionable: more airflow under the plants, or thin the interior growth.
Check it at the worst moment, an hour before lights on, not when you happen to walk past.
The same mistake in the drying room
This one is November specific and it ruins more harvests than the tent version.
A hygrometer sitting on a shelf in a room full of hanging plants is reading the room. The air inside a hanging cola, or in the middle of a loaded drying rack, is considerably wetter. That is why a dry can look finished on the meter and still have wet stems, and why rot appears in hung plants in a room that was supposedly at 60 percent the whole time.
Put the sensor among the hanging plants, in the densest part of the rack. Expect a worse number than the shelf gave you. The worse number is the true one.
Cheap sensors are mostly fine, in one way
The accuracy of a ten dollar hygrometer is not great, but it is consistent enough to compare against itself and against another unit of the same model. For spotting a gap between two places in a room, which is what this is about, that is sufficient.
What is not sufficient is one sensor. A single reading from a single location gives you a number with no context and a lot of confidence, which is the worst combination available.
Buy two or three. They cost less than a bottle of nutrients, and hitting the numbers consistently is worth more than most of what people buy instead.
The honest summary
Most growers who say their environment was fine are reporting a wall reading. The plant never experienced that number.
Move the sensor into the canopy this week, look at it an hour before lights on, and find out what your plants have actually been living in. It is the cheapest correction available and it is one measurement away.
The guides behind this
- First GrowTemperature And HumidityTarget temperature and humidity for every stage of a cannabis grow, cheap ways to hit those numbers, and why late flower humidity is the one to guard.
- Plant DoctorBud RotGray fuzzy mold inside dense buds, usually spotted as one dead sugar leaf. What to cut, what to throw away, and why you cannot smoke it.